Formoa 017FE metal to metal bonding adhesive

Best Glue for Metal to Metal: When Is Formoa 017FE the Right Choice?

The short answer: the best glue for metal to metal depends on whether the joint needs to move. For metal joints on vehicles, trailers, boats and frames that flex, vibrate or change temperature, we recommend Formoa 017FE, a flexible one-part MS polymer that bonds most metals without a primer. For rigid joints that carry heavy loads and mustn't move, an epoxy or a Purok or Aerok MMA adhesive is stronger. Glue can replace welding in the right joint, but only if the joint is designed for it.

This post is for anyone choosing an adhesive to stick metal to metal, or wondering whether glue can replace welds, rivets or bolts. We sell 017FE, so we'll be honest about where it isn't the answer.

Formoa 017FE white flexible structural adhesive 290ml cartridge

Can glue really replace welding?

Sometimes. Forgeway's article on joining metal without welding puts it in perspective: a weld is very strong for its size, with a one-inch weld able to hold around a tonne. An adhesive gives less strength per square millimetre, so it needs more bond area to do the same job. Given enough area, and sometimes some structural support, adhesives can match welding.

Here's how the three main options compare:

Welding Mechanical fasteners Adhesive
Strength Highest per mm² Point loads can loosen or fail over time Can match welding with enough bond area
Dissimilar materials No Yes Yes, including GRP and composites
Heat and distortion Can distort thin metal None, but drilling creates swarf None
Downsides Needs skilled welders and fume extraction Often the most expensive Needs surface prep and cure time
Reversible? No Yes, easily No

Forgeway's own view is balanced: if you have a skilled welder and proper extraction and need a robust joint, welding is still hard to beat. Adhesives win on weight, cost, safety and mixed materials.

Which type of metal glue should you choose?

Forgeway's guide to choosing a metal bonding glue describes four families:

  • Epoxy: the strongest and very versatile, with good heat and chemical resistance. Usually slow to cure and needs thorough surface prep.
  • Acrylic (MMA), such as Purok or Aerok: very high strength, a fast cure and little surface prep. It has a strong smell.
  • Polyurethane: versatile and very flexible, but needs extensive prep and contains harmful substances.
  • MS polymer, such as Formoa 017FE: the most flexible and primerless, but lower in strength, so it's semi-structural.

How do you decide between strength and flexibility?

Ask three questions.

  1. How heavy is the part, and how big is the bond area? Forgeway's rule: the heavier the part, the more strength you need, and the bigger the bond area, the less you need. A light sandwich panel with a wide bond line needs far less adhesive strength than a heavy metal frame on a narrow one. Forgeway treats around 15 MPa as high strength.
  2. Will the joint move? Vibration, flexing and temperature changes all work a joint. Rigid adhesives resist movement until they crack. Flexible adhesives move with it.
  3. How long does it need to last? Forgeway's point is that a very strong bond is no use if it fails after two years of vibration and weather. Durability matters as much as the strength figure on day one.

Why do we recommend Formoa 017FE for metal to metal?

Because most metal-to-metal joints we're asked about are on things that move: van bodies, trailers, buses, boats and frames. For those, 017FE gives the best balance:

  • Strength: 4 MPa tensile and 2.7 N/mm² lap shear, which makes it one of the strongest one-part MS polymers available.
  • Flexibility: 300% elongation at break, so it absorbs vibration and thermal movement.
  • Primerless on most metals: with Formoa Surface Activator for extra security.
  • Proven: Forgeway customers use it to bond stainless panels on buses, GRP domes onto steel minibus frames and GRP panels into box vans.
  • Safer to use: isocyanate- and solvent-free, with no mixing.

The prep varies by metal. We've written separate guides for aluminium, stainless steel and galvanised steel.

When is 017FE the wrong glue?

  • Rigid, heavily loaded joints. If the joint mustn't move and carries a big load, choose an epoxy or a Purok or Aerok MMA. Email us and we'll recommend one.
  • Hot joints. MS polymers aren't suitable above about 150°C.
  • Deep, enclosed joints. It cures from moisture in the air, so a joint with no air access will cure very slowly.
  • When you need speed. It skins in about 10 minutes, has a maximum open time of about 20 and takes roughly 4 to 24 hours to reach handling strength. An MMA cures much faster.

How do you design a joint for glue?

  • Maximise the bond area. Overlap joints beat butt joints every time.
  • Load it in shear. Adhesives are strongest when the parts slide against each other, and weakest when one part is peeled or levered off the other.
  • Keep a bond line of 1 to 2 mm. That's Forgeway's recommendation. Clamping too hard squeezes the joint dry.
  • Support heavy parts while they cure. And where loads are high, add structural support.

How much does it cost?

At Gludog, checked November 2026: Formoa 017FE 290 ml is £11.95, the 600 ml foil pack is £15.15, Surface Activator is £15.49 a litre, and the Cox Air Flow 3 pneumatic gun is £120. Compared with skilled welding time and fume extraction, the adhesive is usually the cheapest part of the job.

What should you do next?

Work out whether your joint moves, then test a sample before you commit. If you're not sure, email sales@gludog.com with the metals, the load and what the part does, and we'll tell you honestly whether 017FE or a rigid structural adhesive is the right call.

Based on Forgeway's guides to metal bonding glue and joining metal without welding. Prices checked November 2026.

Back to blog