Formoa 017FE white flexible structural adhesive for bonding aluminium

Aluminium Glue: Is Formoa 017FE the Best Adhesive for Bonding Aluminium?

The short answer: for most aluminium bonding jobs on vans, trailers, boats and fabrications, a flexible MS polymer adhesive is the best all-round aluminium glue, and Formoa 017FE is the one we recommend. It bonds clean aluminium without a primer, stays flexible as the metal expands, contracts and vibrates, and is one of the strongest one-part MS polymers available. If you need a rigid joint with very high strength, an epoxy or a Purok or Aerok MMA adhesive is stronger, but far less forgiving.

This post is for anyone choosing a glue for aluminium, whether you're bonding panels on a van body, trims on a boat or brackets in a workshop. We sell 017FE, so we'll be clear about where other adhesives beat it.

Formoa 017FE white flexible structural adhesive 290ml cartridge

Why is aluminium harder to glue than it looks?

Bare aluminium quickly grows a thin oxide layer on its surface, and that layer weakens a bond. Forgeway's advice is to remove it before bonding, most commonly by abrading the surface with sandpaper or an abrasive pad such as Scotch-Brite. Timing matters: abrade immediately before the adhesive goes on, because the oxide starts to come back.

The finish matters too. Anodised, brushed, plasma-treated and high-purity aluminium can all change how well an adhesive sticks. If you're working with one of those, test first or ask us.

What types of aluminium glue are there?

Four adhesive families are used on aluminium. Forgeway's guide to choosing the best glue for bonding aluminium compares them like this:

Adhesive Lap shear strength (up to) Surface prep Cure Flexibility
Epoxy 30 MPa Full prep for maximum strength Handling strength in hours, full cure in about a week Brittle unless impact-modified
MMA (acrylic) 25 MPa The least of the four Fastest: snap cure Brittle unless impact-modified
Polyurethane 20 MPa Full prep for maximum strength About a week Highly flexible
MS polymer (e.g. Formoa 017FE) 5 MPa Primerless; an activator may help About 3 mm per 24 hours, depending on moisture The most flexible

On strength alone, epoxy wins. But Forgeway's overall verdict is that an MS polymer is the best glue for aluminium in most applications, because strength is only part of what makes a joint last.

Why does flexibility matter so much on aluminium?

Aluminium moves. It expands and contracts with temperature more than steel does, and on a vehicle, trailer or boat the joint also takes vibration every time it's used. Where aluminium meets a different material, such as steel, GRP or plywood, the two sides move by different amounts. A rigid adhesive has to fight all of that, and over time it can crack. A flexible adhesive moves with the joint instead.

Formoa 017FE has an elongation at break of 300%, according to Forgeway, so it can take that movement while still carrying load.

Why do we recommend Formoa 017FE for aluminium?

  • It's strong for an MS polymer. A tensile strength of 4 MPa and lap shear strength of 2.7 N/mm² make it one of the strongest one-part MS polymer adhesives available.
  • It's primerless. On clean, abraded aluminium it bonds without a primer. Formoa Surface Activator adds extra security on metals.
  • It handles the weather. Forgeway says it holds its strength in ASTM G154 accelerated weathering tests, and it's UV resistant.
  • It's isocyanate- and solvent-free. You avoid the handling and training requirements that come with many polyurethanes.
  • It's proven on vehicles. Forgeway lists jobs like bonding GRP domes onto steel minibus frames, GRP sandwich panels into box vans and stainless steel side panels onto buses.

Where does 017FE lose?

Honestly, in three places.

  • Rigid, very high-strength joints. If nothing should move and you need maximum strength, an epoxy or a Purok or Aerok MMA adhesive is the better choice. Email us and we'll point you to the right one.
  • Ease of use. 017FE is very thick. Forgeway doesn't recommend a manual gun for regular work: a pneumatic or electric applicator makes it far easier.
  • Working time. It skins in about 10 minutes and has a maximum open time of about 20 minutes, so you need to position parts quickly. Handling strength comes in roughly 4 to 24 hours.

Like all MS polymers, it also isn't suitable for joints that run hotter than about 150°C.

How do you bond aluminium with 017FE?

  1. Dry-fit the parts and mark their position.
  2. Abrade the bond area on the aluminium with a Scotch-Brite pad or similar, just before bonding.
  3. Wipe it clean with a solvent such as isopropyl alcohol and let it dry.
  4. Wipe the bond area with Formoa Surface Activator on a lint-free cloth, in one direction, turning to a clean part of the cloth as you go. Leave it to flash off for about 10 minutes.
  5. Apply 017FE and bring the parts together within the open time. Don't squeeze the joint dry: Forgeway recommends a bond line of 1 to 2 mm.
  6. Support or clamp the parts until the adhesive reaches handling strength.

How much does it cost?

At Gludog, checked November 2026:

The 600 ml pack works out at about 2.5p per ml against 4.1p for the cartridge, so it soon pays back on regular work. For a one-off job, our heavy-duty 290 ml applicator (£25) will do it, but expect hard going.

Is it safe to use?

017FE is isocyanate- and solvent-free, which is a real advantage over many polyurethanes. Treat it as you would any industrial chemical: read the safety data sheet first, wear gloves and work in a ventilated space.

What should you do next?

If your aluminium is anodised, brushed or coated, bond a test piece and check it after a week before you commit to the full job. If you're not sure whether 017FE or a rigid structural adhesive suits your joint, email sales@gludog.com with the materials, the load and how the part will be used. We'll give you a straight answer, even if it's a product we don't sell.

Adhesive comparison figures come from Forgeway's guide to bonding aluminium. Formoa 017FE figures come from Forgeway's product information. Prices checked November 2026.

Back to blog