Formoa MS polymer adhesive and sealant cartridges in a range of colours

What Is an MS Polymer Adhesive, and What Does It Cost in the UK?

The short answer: MS polymer adhesive in the UK costs roughly £7.75 to £15.15 per cartridge or foil sausage, which works out at about 2p to 5p per millilitre. An MS polymer is a one-part, moisture-curing hybrid that bonds and seals in one bead, stays flexible and can usually be painted over. You pay more than you would for cheap silicone, and you may need a better applicator, but you get real bonding strength without isocyanates.

This post is for people who build or repair vans, trailers, caravans, boats and vehicle bodies, and for anyone weighing up whether to switch from silicone or polyurethane. We stock the whole Forgeway Formoa range, so the prices below are our own, checked on our store in November 2026.

Formoa MS polymer adhesive and sealant cartridges in a range of colours

What is an MS polymer adhesive?

MS stands for modified silane. It is a hybrid polymer that sits between silicone and polyurethane. Despite the name, Forgeway points out that MS polymers contain no silicone or urethane polymers.

Most MS polymers, including every Formoa product, are one-part. You gun it out, and moisture in the air cures it from the outside in. That means:

  • no mixing and no pot life to worry about;
  • it skins quickly, but full cure is slow compared with other structural adhesives, and it slows further in dry air;
  • a deep, enclosed joint with no air access will cure very slowly or not at all.

What you get once it has cured is a tough, rubbery bond that moves with the joint. That is why MS polymers are used where panels flex, vibrate or expand with temperature. Our earlier post What is an MS Polymer? covers the background in more depth.

What does an MS polymer adhesive cost in the UK?

Here is what each Formoa product costs at Gludog. Prices are our listed prices before VAT, checked November 2026. The pence-per-millilitre column is the fairest way to compare a 290ml cartridge with a 600ml sausage.

Product What it is for Pack Price (ex VAT) Per ml
Formoa 063 Seal and bond, all-rounder 290ml £7.75 2.7p
Formoa 063 Seal and bond, all-rounder 600ml £13.14 2.2p
Formoa 017FE Flexible structural bonding 290ml £11.95 4.1p
Formoa 017FE Flexible structural bonding 600ml £15.15 2.5p
Formoa 055 Primerless direct glazing 600ml £13.97 2.3p
Formoa 760 Sprayable seam sealant 290ml £12.79 4.4p
Formoa 010 Colours Colour-matched sealant 290ml £13.57 to £14.95 4.7p to 5.2p
Formoa 010 RAL 9016 Colour-matched sealant, traffic white 290ml £9.95 3.4p

Two things stand out. First, the 600ml sausage is much cheaper per millilitre: 017FE drops from 4.1p to 2.5p. Second, the general-purpose seal-and-bond product is the cheapest way into MS polymers, and the specialist products cost more.

Why do some MS polymers cost more than others?

The price follows the job the product is built to do:

  • Strength. Formoa 017FE has a tensile strength of 4 MPa and a lap shear strength of 2.7 N/mm², which makes it one of the strongest one-part MS polymer adhesives available. Formoa 063 is 2 MPa, with more stretch (480% elongation against 300%).
  • Specialist chemistry. Formoa 055 is formulated to bond glass without a primer and reaches handling strength in about 3 hours, which makes it the fastest-curing one-part glass bonding adhesive we stock.
  • Colour. Formoa 010 is made in colour-matched batches, and we list over 100 colour options. A single high-volume colour such as RAL 9016 traffic white costs less than the wider range. Colours outside our listed range are a special order, so email us before you plan around one.
  • Format. Formoa 760 is designed to be sprayed or brushed onto seams and wheel arches, which is a different product from a bead sealant.

Is an MS polymer more expensive than silicone?

Usually, yes. Forgeway's own silicone vs MS polymer article calls MS polymers a premium sealant and mentions cheap silicone at around £3 a tube. But they are not doing the same job. Silicone cannot be painted, has poor grab, and is not strong enough for bonding. Cheap silicone also tends to grow mould in damp places.

So the fair comparison is not "£3 against £8". It is one MS polymer bead that seals and bonds, against a silicone bead plus mechanical fixings or a separate adhesive. If a joint only needs sealing, never gets painted and sits in a dry place, silicone may be the cheaper sensible choice. Our post Silicone vs. MS Polymers goes through the differences.

Against polyurethane, the cost question is different. Every Formoa product is isocyanate-free and UV stable. That removes the isocyanate handling issues that come with many PU products, and Forgeway explains the background in its article on polyurethane adhesive alternatives.

What else will you need to buy?

The cartridge price is not the whole cost. Budget for these where they apply:

  • An applicator. A standard 290ml cartridge works in a manual gun such as our 25:1 ratio applicator (£25). For 600ml sausages you need a foil pack gun: our manual foil pack gun is £31.50, and the Cox Air Flow 3 pneumatic gun is £120. Formoa 017FE is thick, so a powered gun makes long runs much easier, and Formoa 055 needs a pneumatic or electric gun. Formoa 760 needs a spray gun to spray it, such as the Jetflow 3 bead and spray dispenser (£210.53).
  • Surface prep. Formoa Surface Activator (£15.49 for 1 litre) cleans and activates surfaces before bonding.
  • Primers, only where needed. Low surface energy plastics such as polypropylene need Formoa Primer PP (£8.00). Formoa 055 is primerless for adhesion, but on glass without a ceramic frit, best practice is Formoa Pg Glass Primer (£45.00) to block UV at the bond line and hide the adhesive. It is not there to help it stick.

If you are fixing a caravan or motorhome rather than building one, our Caravan & Motorhome Repair Kit (£19.95) bundles Formoa bonding and sealing products for repair work.

When is an MS polymer the wrong choice?

We would rather you buy the right product than the one in this post. An MS polymer is not the best fit when:

  • You need a rigid, very high-strength joint, such as replacing a weld where nothing should move. An epoxy or a Purok or Aerok MMA adhesive is the better choice there.
  • You need fast cure in a deep or enclosed joint. Moisture-curing products are slow, and slower still with no air access.
  • The joint will run hot. Forgeway says MS polymer sealants are not suitable above 150°C, where a high-temperature silicone may suit better.
  • You want an easy, glossy finish on a low-stress joint. Silicone is easier to tool. Of the Formoa range, Formoa 063 finishes more smoothly than most MS polymers. Tool it with soapy water before it skins.

Is it safe to use?

Formoa products are isocyanate-free, which is a real advantage over many polyurethanes, but treat them as you would any industrial chemical. Read the product's safety data sheet before use and wear gloves. Some grades, such as Formoa 010, contain an aminosilane that may produce an allergic reaction in sensitive people.

What should you do next?

If you are not sure which Formoa suits your job, start with the job, not the price. Formoa 063 covers most sealing and light bonding, Formoa 017FE is for joints that carry load, Formoa 055 is for glass, Formoa 760 is for spraying seams, and Formoa 010 is for colour-matched sealing. Each product page has the technical data sheet, and if you email sales@gludog.com with the materials you are joining and how the joint will be used, we will tell you which one we would use and what applicator you need.

Back to blog