iSeam Pro 67 colour-matched adhesive for invisible solid surface seams

Why Can You See the Seam in Your Corian Worktop? 6 Common Causes

The short answer: a Corian seam usually shows for one of six reasons. The adhesive colour is wrong, the edges didn't meet cleanly, dust or dirt got into the glue line, the joint was over-clamped, the seam wasn't sanded back properly, or the pattern in the material makes any joint harder to hide. Most of them are avoidable.

You step back to admire a new worktop and your eye goes straight to the joint. Everything else looks perfect, but there's the line. This post is for anyone fitting, repairing or living with a solid surface worktop who wants to know why seams show and how to stop it. We sell the adhesive, so we'll also be honest about the causes an adhesive can't fix.

iSeam Pro 67 colour-matched adhesive for invisible solid surface seams

1. Is the adhesive the wrong colour?

This is the obvious one. Seam adhesive is coloured to match the material, and a shade that's too light or too dark leaves a line that no amount of sanding will remove. One maker who built a project from solid surface asked for dark grey adhesive, received light grey, and said afterwards that black would have been the right choice. If you aren't sure of your worktop's colour name, find it before you order: it's usually on the supplier's paperwork. Then test a small dab on an offcut before you commit to the visible joint.

2. Did the edges meet cleanly?

Installers say the secret of an invisible joint is perfectly matched edges, plenty of adhesive and tight, aligned clamping. Forgeway's data sheet gives a gap fill of 1 to 2 mm, but that's a tolerance, not a target. The better the edges meet, the thinner the glue line and the less there is to see.

3. Did dust or dirt get into the glue?

Any dust or contamination trapped in the adhesive shows once the joint is finished, and light colours show it most. The data sheet asks for surfaces that are clean, dry and free of dust and grease. Wipe both edges, let them dry, and keep sanding dust away from the joint while you work.

4. Was the joint over-clamped?

Squeeze a joint too hard and you push out too much adhesive. Fabricators call this starving the seam. A starved joint has too little adhesive left in it, which hurts both strength and appearance. The aim is a small, even bead of squeeze-out along the whole joint, which you sand off after it has cured.

5. Was it sanded back properly, and left long enough?

The squeeze-out is sanded flush after the adhesive cures, working through the grits. Don't rush it. iSeam Pro 67 can be sanded after about 30 minutes and reaches full cure in 24 hours, but cold slows the cure, and Forgeway gives an application range of 5°C to 35°C. In a cold workshop, give it longer.

6. Does the pattern work against you?

Solid colours and fine speckles hide a seam best. Strong veining, marble effects and random patterns are harder, because the pattern can't line up perfectly across the join. Distributors of veined designs warn that seams may be more noticeable. A matched adhesive can't fix that, and neither can sanding.

Can a visible seam be fixed?

It depends on the cause. If the problem is colour, sanding won't remove the line. If the joint is also weak, it needs redoing properly. We'd rather say so than promise a miracle: have a fabricator look at it and, if the adhesive colour is the culprit, tell us the brand and colour and we'll help you find a closer match.

What should you do next?

Before you mix a single cartridge, dry-fit the joint, check the edges, and test your adhesive colour on an offcut in daylight. That ten-minute check prevents most of what's above. If you aren't sure which colour you need, email sales@gludog.com with the brand and colour name and we'll point you to the right one. You can see the adhesive on the iSeam Pro 67 page, and what it costs to get set up in our price guide.

One safety note: Part A of the adhesive contains methyl methacrylate, which is highly flammable and can sensitise skin. Use gloves, eye protection and good ventilation, and read the safety data sheet first.

Technical figures come from Forgeway's iSeam Pro 67 data sheet.

Back to blog